Blog › E-commerce Shipping Box
E-commerce Shipping Boxes: FEFCO Style, Flute and Dimensional Weight
By Nguyễn Thành Dân, Founder of Drint ·
Pick the style first, then the board, then the size, and check the carrier bill last. Carriers charge on outside dimensions: UPS divides cubic inches by 139 on Daily Rates, FedEx by 139, and USPS by 139 above one cubic foot. A 6 mm board allowance can push a box into the next whole inch and add a billed pound.
Why it matters: in e-commerce the box is both the shipping container and the first thing the customer opens. A box that is a few millimetres too big costs money on every order.
Key points
- FEFCO 0201 is the regular slotted carton. FEFCO 0427 is the one-piece mailer. 0215 and 0216 add a snap-lock bottom for packing without tape underneath.
- The FEFCO code gives box sizes as internal dimensions, length × width × height. Carriers measure the outside.
- On 18 November 2026, UPS listed a divisor of 139 for Daily Rates and 166 for Retail Rates. FedEx's US page listed 139.
- USPS applies dimensional weight above 1,728 cubic inches (one cubic foot), dividing by 139 for rectangular parcels.
- Edge crush (ECT) is a board test. Box compression (BCT) is a whole-box test. Ask for the number, not just the flute letter.
This article goes deeper on e-commerce than our explainer on FEFCO 0201 vs 0427, which covers the basic difference between the two styles.
Which FEFCO style suits e-commerce?
The European Federation of Corrugated Board Manufacturers (FEFCO) publishes the code catalogue that names box styles. The 12th edition, dated 2022, added a new series, 08, for "Retail and e-commerce packaging". Most online shops still ship in four older styles.
| Style | What it is | Erection, per FEFCO | Drint sample and flat sheet | E-commerce fit |
|---|---|---|---|---|
| FEFCO 0201 | Regular slotted carton; outer flaps meet in the middle | M/A, manual or automated | 300 × 200 × 220 mm on a 1,047 × 429 mm sheet | Large, heavy or mixed orders; outer cartons; tape on both ends |
| FEFCO 0427 | One-piece folder with roll-end walls and a tuck-front lid | M, manual | 250 × 200 × 80 mm on a 573 × 691 mm sheet | Mailers and subscription boxes where the unboxing matters |
| FEFCO 0215 | Tuck-in lid on top, 1-2-3 snap-lock bottom | M, manual | 300 × 200 × 220 mm on a 1,047 × 619 mm sheet | Reopenable boxes for bottles, jars, tools and gift sets |
| FEFCO 0216 | Slotted flaps on top, snap-lock bottom | M, manual | 300 × 200 × 220 mm on a 1,047 × 461 mm sheet | Packing stations that lock the bottom by hand and tape only the top |
The erection marks come from the FEFCO code: M is usually manual, A usually automated, M/A either. FEFCO adds that "some manually erected cases can be closed automatically", naming 0216 as an example.
When the 0201 is the right box
The 0201 uses board efficiently, and FEFCO marks it for manual or automated erection. Drint's page lists single-wall B or C flute for everyday loads and BC double wall for heavy goods or tall stacks. It needs tape or glue on both ends.
Choose it for orders of mixed items, for heavy goods, and for any box packed by machine. It is also the usual outer carton when retail boxes ship in multiples.
When the 0427 mailer is the right box
The 0427 folds by hand without glue or tape. The rolled side walls make it rigid. The lid opens like a book, so its inside is the first printed surface the customer sees.
Drint's 0427 page puts E flute as the usual board for printed mailers up to about 2 kg. It suggests B flute or EB double wall for heavier contents or rougher postal networks. It also warns that a tuck flap under about 20 to 25 mm lets the lid pop open in transit.
When a snap-lock bottom helps
The 0215 and 0216 lock their bottoms with four shaped flaps folded in sequence. Drint's pages give typical single-wall loads of about 2 to 10 kg for the 0215 and 8 to 12 kg for the 0216. Both keep barcodes off the bottom, where the lock slits would cut through them.
For a tamper-evident mailer, Drint's catalogue also has the FEFCO 0421, a self-locking box with double side walls and a tuck lid. For protection inside a 0201, FEFCO 0946 cell dividers separate bottles and jars.
Which flute: B, C, E or BC?
Corrugated board is named by its flute, the wave of paper between the liners. FEFCO describes a corrugator joining three, five or seven papers into single, double or triple wall board. Taller flutes stack better; finer flutes print sharper.
The Wiley Encyclopedia of Packaging Technology gives the standard US flute sizes, as quoted on Wikipedia's corrugated fiberboard page:
| Flute | Flutes per foot | Flute thickness | Drint's working board thickness | Typical e-commerce use |
|---|---|---|---|---|
| A | 33 ± 3 | 4.8 mm | not offered | Cushioning; rare in mailers |
| B | 47 ± 3 | 3.2 mm | 3 mm | Shipping cartons, heavier mailers |
| C | 39 ± 3 | 4.0 mm | 4 mm | Everyday shipping cartons |
| E | 90 ± 4 | 1.6 mm | 1.5 mm | Printed mailers, small boxes |
| BC (double wall) | B and C together | — | 7 mm | Heavy goods, tall pallet stacks |
| BE / EB (double wall) | B and E together | — | 4.5 mm | Heavy mailers with a print-quality face |
Board thickness varies by mill and by liner, so treat these as nominal values. Drint's working thickness is the value its editor uses to convert sizes.
What do ECT and BCT mean?
Edge crush test (ECT) measures how much force a strip of board takes on its edge before it crushes. ISO 3037:2022 specifies the method, with the force "applied in the direction of the flute axis". FEFCO lists it as testing method No. 8. Results are given as force per unit width.
Box compression test (BCT) measures the compression strength of a whole, finished box. FEFCO lists it as testing method No. 50, "Determination of compression resistance". BCT depends on the board, the box size and the style.
For a designer, the practical rule is short. Flute letter is not a strength specification. If the box must stack on a pallet or survive a parcel hub, ask the corrugated supplier for a tested ECT or BCT value. Drint's 0201 page gives the same advice: specify board by edge crush or bursting strength where stacking matters.
Inside or outside dimensions: how do I convert?
The FEFCO code is explicit. "All dimensions are expressed as internal dimensions in mm," given as length × width × height. Length is "the longer dimension at the opening", width the shorter, height from the opening to the base.
FEFCO adds that dimensions are measured on the flat blank "from the centre of crease bearing the thickness of the material in mind". It also sets the climate for measuring: 23 °C and 50% relative humidity, under EN 20187.
Three sizes matter:
| Size | What it is | Who needs it |
|---|---|---|
| Inside (internal) | The space for the product | The packer and the FEFCO order line |
| Crease (manufacturing) | Centre of crease to centre of crease on the blank | The die-maker |
| Outside (external) | The box as the carrier measures it | The carrier bill and the pallet plan |
Drint's editor converts with one board thickness per step on each dimension. Inside to crease adds one thickness; crease to outside adds one more. Its note calls these "usual rules of thumb, not a shop's own allowances". A test die confirms tight fits.
Worked example. A 0201 with inside size 300 × 200 × 100 mm in B flute, at Drint's 3 mm:
- Crease size: 303 × 203 × 103 mm.
- Outside size: 306 × 206 × 106 mm.
Each dimension grows by 6 mm. A 0201 closes with two sets of flaps at each end, and board thickness varies by mill. Ask your corrugated supplier for the outside size it will actually deliver, and measure a sample before you lock the carrier rate.
How do carriers calculate dimensional weight?
All three US carriers compare actual weight with dimensional weight and bill the greater. Their published rules differ in divisor, rounding and threshold.
| Carrier | Divisor (in³ per lb) | Measurement rounding | Threshold | Source wording, accessed 18 November 2026 |
|---|---|---|---|---|
| UPS | 139 Daily Rates; 166 Retail Rates | Round up each side to the next whole inch | "May apply to all" domestic and international package services | "The divisor varies by rate type: 139 for Daily Rates; 166 for Retail Rates." |
| FedEx | 139 | Each side to the nearest whole inch | Not stated on the page | "Dividing by 139 for U.S., Puerto Rico, and international shipments." |
| USPS (Priority Mail, Ground Advantage) | 139 for rectangular parcels | Round up each side to the next whole inch | Over 1,728 in³ (1 cubic foot) | "divide the result by 139 and round up … to the next whole number" |
UPS says to "increase any fraction to the next whole pound". USPS rounds the result up too, and caps dimensional weight at the 70-pound price. FedEx's dimensional-weight page does not say how it rounds the result. Its 2026 Service Guide rate pages state: "Any fraction of a pound is rounded up to the next-higher pound."
The USPS steps for rectangular parcels carry revision markers reading "7-12-26" in the Domestic Mail Manual. Nonrectangular parcels at retail and commercial Priority Mail use an extra factor of 0.785 before dividing.
Worked example 1: a 30 × 20 × 10 cm box
The outside size converts to 11.81 × 7.87 × 3.94 in. Rounded up, that is 12 × 8 × 4 in, or 384 cubic inches.
| Carrier | Calculation | Dimensional weight |
|---|---|---|
| UPS Daily Rates | 384 ÷ 139 = 2.76 | 3 lb |
| UPS Retail Rates | 384 ÷ 166 = 2.31 | 3 lb |
| FedEx | 384 ÷ 139 = 2.76 | 3 lb at FedEx's whole-pound rates |
| USPS | 384 in³ is under 1,728 | Not applied; actual weight is billed |
A 1 kg product (2.2 lb) in this box is billed at 3 lb by UPS and rated at 3 lb by FedEx.
Worked example 2: the 6 mm that costs a pound
Take the inside size from the conversion example, 300 × 200 × 100 mm. Someone quotes it to the carrier as if it were the outside. It rounds to 12 × 8 × 4 in, or 384 cubic inches: 3 lb at UPS Daily Rates.
The real outside is 306 × 206 × 106 mm, or 12.05 × 8.11 × 4.17 in. UPS rounds each side up, to 13 × 9 × 5 in. That is 585 cubic inches, and 585 ÷ 139 = 4.21, billed as 5 lb.
The fix is in the design. Inside 298 × 197 × 95 mm gives an outside of 304 × 203 × 101 mm. All three sides stay under 12, 8 and 4 in, and the box bills at 3 lb again.
FedEx's "nearest whole inch" rule rounds 12.05 × 8.11 × 4.17 in down to 12 × 8 × 4. The same box can bill differently at two carriers.
Worked example 3: crossing one cubic foot at USPS
A 40 × 30 × 30 cm box is 15.75 × 11.81 × 11.81 in, rounded up to 16 × 12 × 12 in. That is 2,304 cubic inches, over the USPS threshold.
- UPS Daily Rates: 2,304 ÷ 139 = 16.58, billed as 17 lb.
- UPS Retail Rates: 2,304 ÷ 166 = 13.88, billed as 14 lb.
- USPS: 2,304 ÷ 139 = 16.58, billed as 17 lb.
- FedEx: 2,304 ÷ 139 = 16.58, rated as 17 lb.
Seventeen pounds is about 7.7 kg. A light product shipped in this box pays for the air around it.
Where should the unboxing print go?
In a 0201, most print is outside. Drint's 0201 page notes that cartons are usually printed flexo in one to three colours, with brand, handling marks and stacking limits. FEFCO describes flexo as the common process for corrugated, with digital direct print entering the market.
In a 0427, the print areas follow the opening:
- Lid top, the face the customer sees on the doorstep.
- Inside of the lid, the first face seen when the box opens.
- Inner walls and floor, seen as the product comes out.
- Front tuck flap, seen for a moment as the lid lifts.
Drint's 0427 page warns about one orientation trap. Inside art laid out the same way as the outside reads upside down when the lid flips open. Rotate it on the dieline.
Keep the tuck crease, the roll-over creases and the lock tabs clear of heavy solids, which crack when folded. Keep the shipping label zone plain. A carrier label covers whatever artwork sits there.
What are the common mistakes?
- Quoting inside sizes as outside sizes. Carriers measure the outside, and rounding turns millimetres into whole inches.
- Oversizing for one tall item. One product sets the height of every box in the run. Consider a second size.
- Choosing by flute letter alone. Two boards with the same flute can use very different papers. Ask for tested values.
- Flute running the wrong way. Drint's 0201 page notes that flutes should run vertically for stacking strength.
- A short tuck flap on a mailer. Under about 20 to 25 mm, the lid can open in sorting, per Drint's 0427 guidance.
- Barcodes on snap-lock bottoms. The lock slits cut through them.
- Inside art printed the wrong way up. It reads correctly only when rotated for the opening lid.
What this means for designers
Write the size line in full: style, inside size, board and flute. For example: "FEFCO 0427, inside 250 × 200 × 80 mm, single-wall E flute, white top liner."
Then convert to the outside size and check it against whole inches before you design. A box that clears each inch by a millimetre or two can cut a billed pound from every order.
Design the unboxing in the order the customer sees it: lid, inside lid, interior, product. Leave the label zone and the lock tabs clean.
Try it
Open the FEFCO 0427 mailer dieline, choose inside size and type 298 × 197 × 95 mm. Check the outside size Drint reports, then turn the box in 3D. Compare the same size as a FEFCO 0201 shipping carton or a FEFCO 0216. Every other style is on the FEFCO and ECMA code list.
Sources
- FEFCO, FEFCO Code: Design style library for corrugated board products, 12th edition, 2022, fefco.org, PDF read 18 November 2026.
- FEFCO, "Testing methods & recommendations", fefco.org, accessed 18 November 2026.
- FEFCO, "The production of modern corrugated packaging", fefco.org, accessed 18 November 2026.
- International Organization for Standardization, ISO 3037:2022, "Corrugated fibreboard — Determination of edgewise crush resistance (non-waxed edge method)", abstract, iso.org, accessed 18 November 2026.
- UPS, "Package Dimensions, Size Limits and Weight Guide", FAQ "What is dimensional weight and how do I calculate it?", ups.com, accessed 18 November 2026.
- FedEx, 2026 FedEx Service Guide, PDF, rate pages, accessed 18 November 2026.
- FedEx, "What is dimensional weight?", fedex.com, accessed 18 November 2026.
- United States Postal Service, Domestic Mail Manual 123 (Retail Priority Mail), section 1.3, pe.usps.com; DMM 133 (USPS Ground Advantage, Retail), section 1.4, pe.usps.com; DMM 223 (Commercial Priority Mail), section 1.4, pe.usps.com, all accessed 18 November 2026.
- Wikipedia, "Corrugated fiberboard", flute table citing G. Foster, "Boxes, Corrugated", The Wiley Encyclopedia of Packaging Technology, 2nd ed., 1997, wikipedia.org, accessed 18 November 2026.
- Drint, FEFCO 0201, 0215, 0216, 0421, 0427 and 0946 dieline pages, drint.io/dielines/codes, checked 18 November 2026; size conversion rule from Drint's dieline editor on the same date.
Frequently asked questions
What is the best FEFCO box for e-commerce?
FEFCO 0427 is the usual mailer for small and medium items where presentation matters. FEFCO 0201 suits heavy, large or machine-packed orders.
Does FEFCO use inside or outside dimensions?
Inside. The 12th edition of the FEFCO code says all dimensions are internal, as length × width × height in millimetres.
What divisor does UPS use for dimensional weight?
UPS listed 139 for Daily Rates and 166 for Retail Rates on 18 November 2026.
Does USPS charge dimensional weight on small boxes?
Not under its published rule. USPS applies it only to parcels over 1,728 cubic inches, one cubic foot.
Is E flute strong enough for shipping?
For light printed mailers, often yes. Drint's guidance puts E flute up to about 2 kg in a 0427. Heavier goods need B flute or double wall.
What is the difference between ECT and BCT?
ECT tests a strip of board on its edge. BCT tests a whole finished box under compression.