Blog › Stand-Up Pouch Sizes
Stand-Up Pouch Sizes: Dimensions, Fill Weights and Dieline Anatomy
By Nguyễn Thành Dân, Founder of Drint ·
A stand-up pouch (doypack) is sized as width × height + bottom gusset. For 150 g of whole-bean coffee, suppliers list about 130 × 210 mm with an 80 mm gusset. For 250 g, about 160 × 220 mm with a 70 mm gusset. No standard fixes these sizes. They vary by supplier, by product density and by where the zipper sits.
Why it matters: the pouch size sets the printable face. Seals, the zipper and the folded base take a large share of it. Artwork drawn on the full flat outline, without those zones, is the most common pouch mistake.
Key points
- Stand-up pouches are quoted as width × height + gusset, in that order, in millimetres or inches.
- The gusset figure is the full depth of the base. It folds in half inside the pouch, so each face loses about half of it at the bottom.
- Published size charts disagree. One Australian supplier listed four different sizes, all sold as 150 g pouches, on 18 November 2026.
- Coffee, flour and snacks fill the same pouch to very different weights. Size by volume, then confirm with a fill test.
- Drint's pouch dieline marks seals and the zipper line as dashed lines. Keep small text and barcodes out of them.
What are the standard stand-up pouch sizes?
There is no ISO or industry-wide size standard for stand-up pouches. Converters publish their own charts, and those charts are written for their own films and machines. The tables below are what four sources stated on 18 November 2026. They are starting points, not specifications.
Coffee: sizes from a coffee-bag converter
Guangzhou-based QIYU PACK lists "common sizes of the coffee bags in the coffee market". Its stand-up pouch rows read:
| Stated capacity | Width × height + gusset (mm) |
|---|---|
| 50 g | 100 × 190 + 60 |
| 100 g | 128 × 210 + 80 |
| 200 g | 160 × 240 + 60 |
| 250 g | 160 × 220 + 70 |
| 340 g (12 oz) | 180 × 240 + 90 |
| 454 g (16 oz) | 180 × 280 + 100 |
| 500 g | 230 × 280 + 100 |
| 908 g (2 lb) | 230 × 340 + 120 |
The chart does not say whether capacity means beans or ground coffee. Note that the 200 g row is taller but has a shallower gusset than the 250 g row. Gusset depth changes capacity as much as height does.
Coffee: sizes with a stated basis
Vivopak, an Australian pouch supplier, states the basis for some of its capacities. Its 150 g pouch at 130 × 210 mm with an 80 mm bottom gusset is "Based on whole bean coffee". So is its 400 g pouch at 180 × 260 + 80 mm.
The same store also sold 150 g pouches at 140 × 200, 130 × 200 and 140 × 190 mm, each with an 80 mm gusset. Four sizes for one label shows how loose "150 g" is as a size name.
Coffee beans against flour: one pouch, two weights
UPrinting, a US online printer, publishes a chart in inches with volume in cups and two fills: coffee beans and flour. Flour stands in here for fine powders. The millimetre values are Drint's conversions.
| Size (in) | Size (mm, approx.) | Volume | Coffee beans | Flour |
|---|---|---|---|---|
| 5 × 7 × 3 | 127 × 178 + 76 | 1½ cups | 5 oz (142 g) | 10 oz (283 g) |
| 5.75 × 7.5 × 2.5 | 146 × 191 + 64 | 2¼ cups | 7 oz (198 g) | 1 lb (454 g) |
| 6.75 × 8.5 × 3.5 | 171 × 216 + 89 | 3¾ cups | 11 oz (312 g) | 1 lb 9 oz (709 g) |
| 7 × 9 × 3 | 178 × 229 + 76 | 4½ cups | 13 oz (369 g) | 2 lb (907 g) |
| 8.125 × 10 × 3.5 | 206 × 254 + 89 | 8½ cups | 1 lb 8 oz (680 g) | 3 lb 3 oz (1,446 g) |
| 9.875 × 10.5 × 3 | 251 × 267 + 76 | 11½ cups | 2 lb 1 oz (936 g) | 4 lb 7 oz (2,013 g) |
The same pouch holds roughly twice the weight in flour as in whole beans. That is the single most useful fact in any pouch chart: weight labels only hold for the product they were measured with.
Snacks, nuts, powders and pet food: Drint's sample sizes
Drint's pouch mockups each open at a sample size built for one product. These are the defaults on the public pages on 18 November 2026. They carry no fill weight, because Drint has not fill-tested them.
| Drint mockup | Product on the page | Sample size (W × H + base, mm) |
|---|---|---|
| Stand-up zip gummy pouch (D-10499) | Fruit gummies | 120 × 170 + 60 |
| Zip tea pouch (D-10199) | Tea, dried flowers | 120 × 180 + 60 |
| Stand-up zip coffee pouch (D-10090) | Coffee, one-way valve, zip | 130 × 200 + 70 |
| Zip snack pouch (D-10200) | Puffs, chicken jerky | 140 × 210 + 70 |
| Stand-up zip cashew pouch (D-10495) | Salted roasted cashews | 140 × 220 + 80 |
| Stand-up zip cereal powder pouch (D-10497) | Cereal powder, matcha | 160 × 250 + 90 |
| Stand-up zip pet food pouch (D-10498) | Cat kibble | 170 × 260 + 90 |
| Stand-up zip pouch (D-10500) | Rice, nuts, flour | 220 × 320 + 110 |
Snacks such as puffs are light and bulky, so they need far more volume per gram than coffee. Pet treats range from dense jerky strips to airy biscuits. KimEcopak, a Canadian pouch supplier, lists a 230 g (8 oz) pouch at 15 × 23 × 8 cm as best for nuts, dried fruit, snacks and granola. It does not say which product that weight was measured with. No chart read for this article gives a tested fill weight for puffs or pet treats.
Work it out from bulk density instead: fill weight ≈ usable volume × bulk density. UPrinting's chart shows the method. Its 1½-cup pouch, about 355 ml, holds 142 g of beans or 283 g of flour. That implies about 0.40 g/ml for beans and 0.80 g/ml for flour.
Illustrative arithmetic, not a supplier specification: suppose a level 250 ml cup of your puffs weighs 30 g. That is 0.12 g/ml. The same 355 ml pouch would then hold about 355 × 0.12 = 43 g. Settling and headspace change the real figure, so confirm with a fill test. KimEcopak puts it plainly: "Never assume the volume by external dimensions alone."
How is a stand-up pouch built?
A stand-up pouch is two printed faces and a base panel, heat-sealed together. Drint's mockup page describes it as "two laminate faces plus a W-folded bottom gusset". The base opens when the pouch is filled, and the pouch stands.
The film is a laminate of two or three plies. A print layer sits outside, an optional barrier layer in the middle, and a sealant layer inside. Rotogravure often prints in reverse on the inside of the outer film, so the ink sits between plies.
Bottom gusset types: round, K-seal and plow
| Base | How it is sealed | What sources say it suits |
|---|---|---|
| Round bottom (Doyen) | A U-shaped seal joins the base to both faces | The most common food style; products under 1 lb, per the Institute of Food Technologists (IFT) |
| K-seal | Diagonal seals at the bottom corners form a "K" | Heavier products; the angled seals relieve stress on the faces |
| Plow (corner) bottom | One folded web, no seal across the base | Products over 1 lb; the product sits on a flat floor |
Aaron L. Brody wrote in IFT's Food Technology in March 2013 that the round bottom gusset "is applied for products weighing less than one pound". He described the K-style as "designed for heavier products". The plow style "is mainly used for products weighing more than one pound due to its stability."
The base type changes the artwork. On a round or K-seal pouch, the lower corners of each face are seal, not print. On a plow bottom, the faces run down to a fold, so more of the front stays visible.
Zipper, tear notch, hang hole and valve
- Zipper. A press-to-close zipper runs across the inside of both faces, below the top seal. Drint's mockup page puts it 20 to 30 mm below the top seal. Drint's pouch dieline starts the zip line 35 mm from the mouth by default.
- Tear notch. A small V cut into each side seal, between the top seal and the zipper. ePac Flexible Packaging describes notches that "sit directly below the heat/cold seal area". Drint draws one on each side seal.
- Hang hole. A punched hole in the top seal for peg display. ePac offers "a traditional round hole or a sombrero hole". Drint's die can add a euro-slot hang hole in the top seal.
- One-way valve. Coffee bags often carry a degassing valve. Drint places it on the back, centred, under the zipper, never over the front artwork.
Seal widths
Drint's pouch editor sets an 8 mm seal by default. It warns below 5 mm, with the note that film pouch seals are usually 8 to 10 mm. It also stops a zipper placed less than 5 mm under the top seal, or more than 40% of the height down.
Those are Drint's checks, not a standard. Your converter's sealing jaws decide the real width. Ask for it before you lay out the artwork.
Where is the safe area for artwork?
The safe area is what is left after you remove every zone that is sealed, cut, punched or folded out of sight. On a stand-up pouch that means five zones:
- Side seals on both edges of each face.
- The top seal, including any hang hole.
- The zipper band, plus the strip between it and the top seal, where the tear notch sits.
- The lower part of each face, which curves into the base seal when the pouch stands.
- The gusset itself, which is printable but faces the shelf floor.
Drint's pouch dieline draws the seal edges and the zip line as dashed lines. Its info note reads, in short: keep small text and barcodes out of the seal zones. The base is drawn below the two faces as its own panel, with a crease at half its depth where it folds.
No single clear margin applies to every pouch. Two converters' artwork guides, read on 18 November 2026, show how the rule is set.
- pack-on GmbH, which runs the Packaging Warehouse web shop, asks for "a safety margin of at least 3.0 mm on all sides from the die-cut contour and the bottom fold". It wants 2 mm of bleed beyond the die cut. It says no text or other important elements should sit in the sealing area or the zipper position.
- Roastar gives no single figure. It draws the safe area as green lines on a template made for each product and material. It asks for 1/16-inch (about 1.6 mm) bleed. On its paper-based films, ink "cannot print in areas of the pouch where heat is applied", meaning heat seals, zipper and valve areas.
Use your converter's template for your exact pouch. Margins vary by converter, film and machine.
How do I measure a stand-up pouch?
Measure the empty pouch lying flat, with the base folded in.
- Width: across the face, edge to edge, including the side seals.
- Height: from the top edge to the bottom of the folded base. UPrinting measures it "from the top end of the pouch to the bottom of the gusset".
- Gusset: the full depth of the base when opened out. On the flat pouch you see only half of it.
Write the result as width × height + gusset. Say whether the height includes the gusset, because some charts do not. For volume, UPrinting advises measuring the fillable area from below the zipper, not from the top edge.
Worked example: a 150 g coffee bag
A roaster wants a 150 g bag of whole beans, with a zipper and a valve.
Step 1, start size. Vivopak's 130 × 210 + 80 mm pouch is rated 150 g on whole beans. UPrinting's 127 × 178 + 76 mm pouch holds 5 oz (142 g) of beans. QIYU's 100 g bag is 128 × 210 + 80 mm. A start of 130 × 210 + 80 mm fits all three.
Step 2, ground or whole. Ground coffee packs denser than beans. A ground 150 g fill may need a shorter pouch, which only a fill test can confirm.
Step 3, face area. With Drint's 8 mm seals, the printable width is 130 − 16 = 114 mm. The zipper sits 35 mm from the top. The 80 mm base folds into 40 mm on each face. That leaves about 210 − 35 − 40 = 135 mm of clear height for the main panel.
Step 4, back face. The valve goes on the back, under the zipper. Keep the ingredients, roast date and barcode below it, and clear of the side seals.
So the hero area is roughly 114 × 135 mm on a pouch that measures 130 × 210 mm. Design for that rectangle, not for the outline.
What are the most common pouch artwork mistakes?
- Artwork on the seals. Sealing jaws crush and distort the seal area. Small type there becomes unreadable, and barcodes stop scanning.
- Text across the gusset fold. On a round-bottom pouch the lower face curves into the base. A line of copy there bends out of view on the shelf.
- The zipper line through the logo. The zipper is a ridge inside the film. It shows through as a line and can split a logo or headline.
- One size for every product. A chart built on coffee beans undersizes a powder label claim and oversizes a snack bag. Test with the real product.
- Ignoring the gusset in the size. "130 × 210" without the gusset is half a specification. The base decides capacity and how the pouch stands.
- Bright colours on bare metallised film. Drint's mockup page notes that unbacked areas "shine like metal". Ask for a white underprint where colours must stay bright.
What this means for designers
Ask the converter for three numbers before you draw: seal width, zipper position and gusset depth. Then build the artwork on a dieline at that exact size, not on a generic template.
Check the pouch standing up, not only flat. A flat proof hides the curve at the base and the shadow line of the zipper. A 3D turn shows both before the film is printed.
Keep weight claims out of the brief until a fill test confirms them. The same pouch can hold 142 g of beans or 283 g of flour.
Sources
- QIYU PACK, "Custom Coffee Packaging Bags & Pouches Manufacturer", coffee bag size chart, qiyupack.com, accessed 18 November 2026. Supplier chart; sizes vary by supplier.
- Vivopak, "150g All Clear Stand Up Pouch with Zipper (130×210+80mm)", vivopak.com.au, accessed 18 November 2026.
- Vivopak, "400g Frosted Clear Stand Up Pouch with Zipper (180×260+80mm)", vivopak.com.au, and stand-up pouch listing page 2, vivopak.com.au, accessed 18 November 2026.
- UPrinting, "How to Choose the Right Pouch Size for Your Product", uprinting.com, accessed 18 November 2026.
- Aaron L. Brody, "Stand Up and Spout", Food Technology, Institute of Food Technologists, 1 March 2013, ift.org, accessed 18 November 2026.
- ePac Flexible Packaging, "The Different Types of Stand-Up Pouches", epacflexibles.com, accessed 18 November 2026.
- ePac Flexible Packaging, "Anatomy of a Flexible Pouch: Skirt Seal Pouch & Plow Bottom Pouch", epacflexibles.com, accessed 18 November 2026.
- Drint, stand-up pouch mockup pages and sample sizes, drint.io/mockups/type/pouches, checked 18 November 2026; seal, zipper and gusset checks from Drint's pouch dieline editor on the same date.
- pack-on GmbH, Packaging Warehouse, "Print file check for stand-up pouches & flat pouches", packaging-warehouse.com, accessed 18 November 2026.
- Roastar, "Artwork Setup Guide: Stand-Up Pouch", PDF, roastar.com/artwork-specs (PDF), accessed 18 November 2026.
- KimEcopak, "Pouch Packaging Size Chart: Find the Perfect Fit by Product Type", kimecopak.ca, accessed 18 November 2026.
Try it
Open the stand-up zip coffee pouch and type 130 × 210 mm with an 80 mm base. Turn it in 3D to check the zipper line and the base curve. Browse all film pouch mockups or the coffee pouches for other shapes. When the artwork is ready, follow from artwork to a print-ready packaging file.
Frequently asked questions
What size stand-up pouch do I need for 250 g of coffee?
One coffee-bag converter lists 160 × 220 mm with a 70 mm gusset for 250 g. Sizes vary by supplier and by bean or ground fill, so test with your coffee.
Is the gusset included in the height?
Often it is. UPrinting measures height to the bottom of the gusset. Some suppliers do not, so ask which convention a quote uses.
What is the difference between a doypack and a flat-bottom pouch?
A doypack has a folded base that opens into an oval. A flat-bottom pouch has a square base and side gussets, and stands like a box.
How wide are the seals on a stand-up pouch?
Drint's editor defaults to 8 mm and notes 8 to 10 mm as usual. Your converter's equipment sets the real value.
Can I print on the bottom gusset?
Yes. The base is printed as part of the same film. It faces the shelf, so keep it for secondary information.
Which bottom style is best for heavy products?
IFT's Food Technology described K-style and plow bottoms as the choices for heavier products, above about 1 lb.